Two Elastomers Let One All-Soft Robot Crawl, Jump, Climb and Roll
Researchers laminated a reconfigurable liquid-crystal elastomer with a fast dielectric-elastomer actuator to build a 0.45-gram robot that crawled at 2.3 cm/s, jumped more than 2.5 body lengths, climbed a 20-degree slope and rolled. The laboratory machine carried five times its weight, but still required high voltage, heating and wired power.
Researchers have built an entirely soft robot that can switch among crawling, jumping, slope climbing and rolling without adding a rigid skeleton. The 0.45-gram laboratory machine combines two elastomers in one bonded structure: one slowly changes its resting shape, while the other supplies fast motion.
The 30-second summary
- What happened? A team led by Zhejiang University laminated liquid-crystal and dielectric elastomers into one electrically controlled robot.
- Why does it matter? The two materials divide the jobs of body reconfiguration and rapid actuation, allowing several movement modes without a conventional hard frame.
- What is the catch? The prototype used high electric fields, resistive heating and external wires, and its durability was not demonstrated in a real environment.
Key Number: five times its own weight. The robot maintained locomotion while carrying that payload in laboratory tests, although the paper does not establish useful untethered transport.
A soft skeleton paired with an artificial muscle
Many soft robots use one active material attached to stiff supports or several separate actuators. Those combinations can create interfaces where very different stiffnesses meet, increasing structural complexity and the risk of delamination.
The new design uses a monolithic heterolayer elastomer. A liquid-crystal elastomer acts as a reconfigurable skeleton. Steel traces heat it electrically, letting the body bend into a chosen equilibrium shape and hold that configuration. A processable high-performance dielectric elastomer forms the faster artificial muscle. Carbon-nanotube electrodes apply an electric field across that layer, producing rapid deformation that drives movement.
The two materials have complementary weaknesses. The liquid-crystal layer produces large, persistent shape changes but responds relatively slowly. The dielectric layer reacts quickly and delivers higher power, but needs a suitable preconfigured body shape to turn deformation into useful movement.
Four modes from independently controlled halves
The researchers split the electrodes along the robot's centerline so the left and right sides could be controlled independently. Changing the liquid-crystal layer's shape selected the mechanical state; pulsing the dielectric layer then generated crawling, jumping or rolling.
In reported tests, the robot crawled in either direction at up to 2.3 centimeters per second, leapt more than 2.5 body lengths, climbed a 20-degree incline and rolled downhill under control. It also carried loads up to five times its approximately 0.45-gram mass.
A dry-stacking process bonded the elastomer layers. The paper reports more than tenfold greater interfacial strength than simple physical adhesion, addressing one failure point in layered soft machines. The liquid-crystal material was tailored to operate between roughly 30 and 90 degrees Celsius so that heating would not immediately destroy the dielectric layer's electrical performance.
Why multimodal motion matters
A robot that can change locomotion mode may handle transitions that defeat a single gait: crawl across a flat surface, jump an obstacle, climb a slope and roll when gravity makes that efficient. NewTqnia previously covered a light-responsive material that twisted and reset and a spider-inspired robot boat designed for water rescue. The new work focuses instead on integrating complementary actuation materials into one soft body.
The architecture is more important than the particular demonstration. Separating slow body configuration from fast muscle-like actuation could let designers program several behaviors without building a different mechanism for each one.
Before we overstate the result
- The robot was tested on controlled laboratory surfaces and slopes, not rubble, soil, water or another unpredictable setting.
- Dielectric elastomers require high electric fields, while the liquid-crystal layer relies on Joule heating. Both complicate portable power and thermal management.
- The prototype was tethered by electrical connections; no onboard battery, sensing or autonomous controller was demonstrated.
- Layer bonding improved in the reported tests, but long-cycle fatigue, puncture resistance and environmental durability remain unknown.
- Carrying five times a 0.45-gram body is mechanically notable but still represents only a few grams of payload.
The next milestone is untethered operation
A stronger demonstration would integrate compact power electronics, sensing and closed-loop control while preserving the soft structure. The robot would then need to repeat its four modes for thousands of cycles on irregular terrain without overheating or separating at the material interface. Until then, the paper establishes a versatile actuation architecture rather than a field-ready explorer.
Verified topics and entities
Sources and citations3 sources
External references used to support the reporting in this article.
Published by
NewTqnia Robotics Desk
An institutional editorial team within NewTqnia